Log message:
Update to 2.5.2p1, provided by Nick Goffee of BBN.

[bugfixes and minor improvements omitted; see NEWS]

Changes in release 2.5.2

   * krb5 auth is working
   * Works with IPv6 address
   * Amanda configuration file changes
         o amanda.conf changes
               + debugging is enabled in the config file
                 see all debug_* config option
               + tapetype 'readblocksize', if maxtapeblocksize is set too
                 larger for your hardware
   * Amanda command changes
         o amadmin: new 'holding list' and 'holding delete' subcommand.

Changes in release 2.5.1p3

   * Works with tar-1.16 and exit status of 1.

Changes in release 2.5.1p2

   * amoverview is working
   * dumptype starttime is working

   * Amanda command changes
         o amtape accept the -o arguments
         o amgetconf --list to list all tapetype, dumptype, holdingdisk
           or interface
         o amgetconf can return a value of a specific tapetype, dumptype,
           holdingdisk or interface

Changes in release 2.5.1p1

   * Remove contrib/sst.

Changes in release 2.5.1

   * Defects found by Coverity scan and Klocwork K7 analysis tools fixed.
   * Works with GNU tar 1.15.91 - work with new gtar state file format.
   * Open SSL encryption support
   * Two new authentication methods: bsdtcp, bsdudp.
   * Unlimited number of DLEs on a client with bsdtcp, rsh and ssh
     authentication methods.
   * Recovery process amrecover uses Secure API. amoldrecover command
     (same syntax and functionality as amrecover command) is provided for
     compatibility with old Amanda releases. amoldrecover command uses old
     amidxtaped/amindexd protocol.
   * Amanda debug files are separated into client/server/amandad and
     are also classified based on Amanda configuration name.

   * Amanda command changes
         o amfetchdump -o is replaced by -O.
         o amcheck -w option does all tests including the tape writable test.
           Use amcheck -t -w to do only the tape writable test.
         o -o command option to override Amanda configuration. See amanda man
           page for details.
         o amgetconf command doesn't write the BUGGY message when a entry
           is not found in the configuration file.

   * Amanda configuration file changes
         o amanda.conf changes
               + amrecover_do_fsf in amanda.conf defaults to yes
               + amrecover_check_label in amanda.conf defaults to yes
               + usetimestamps in amanda.conf to support multiple
                 backup runs in a calendar day.
               + holdingdisk in amanda.conf supports new values:
                 NEVER, AUTO, REQUIRED.
               + amandad_path, client_username and ssh_keys in
                 amanda.conf for ssh/rsh authentication.
         o New amanda client configuration file - amanda-client.conf.
           Different client configuration file can be used for each Amanda
           configuration.
               + gnutar_list-dir and amandates can be specified in
                 Amanda client configuration file - amanda-client.conf
         o .amandahosts format changes to allow use of secure API for recovery.
         o Amanda service entries in xinetd configuration has changed.

Changes in release 2.5.0p1

* Add the 'amtape update' command.

Changes in release 2.5.0

* Communication security/authentication: Kerberos 4/5, OpenSSH
* Data security: Symmetric/Assymetric encrytion algorithms (aesutil
  and gpg encryption),  Encryption can be done on server or client,
  Custom encryption utilities can be used.
* Compression: Ability to add custom compression tools. This is a
  really useful feature especially since it can specified for a DLE.  You
  can use different compression algorithm for images, binaries, ascii files
  and so on.
* Dump images spanning multiple media volumes - Dump images are no
  longer restricted to a single media volume (tape or vtape).  Data restoration
  can be done using amrecover and amfetchdump commands.
* Auto tape labelling - This optional feature is good for disk backups.

Change in release 2.4.5

* new displayunit global option to select the unit use to display number
  k=kilo, m=mega, g=giga, t=tera.
* new amoverview -skipmissed option.

Change in release 2.4.5b1

* holding disk disk use timestamped directory.
* autoflush flush today's dump.
* new bumppercent global option, this should improve bumping criteria,
  the bumpsize is set to a fixed value which can be adequate for small
  and large disk.
* bumpsize, bumppercent, bumpdays and bumpmult can be in a dumptype.
* calcsize support include and exclude like gnutar.
* new 'estimate' dumptype option to select estimate type:
    CLIENT: estimate by the dumping program.
    CALCSIZE: estimate by the calcsize program, a lot faster but less acurate.
    SERVER: estimate based on statistic from previous run, take second but
            can be wrong on the estimate size.

Log message:
Bump version or revision of all packages that have a runtime dependency
on gzip.

Log message:
Whitespace cleanup, courtesy of pkglint.
Patch provided by Sergey Svishchev in private mail.

Log message:
add patch:
  Make chg-chio wait for a tape to come ready after loading it.
  clean up $MT/@MT@ confusion in chg-chio

Patch from Aaron Grier in PR pkg/35231.
(This resolves issue #1 in the PR; issue #2 is unrelated.)

Log message:
Prevent amverify from looping forever. Patch provided by Jean-Louis
Martineau on amanda-users:
http://groups.yahoo.com/group/amanda-users/message/55099
Pointed out by Jukka Salmi in PR 35361.

Log message:
Remove explicit GNU tar dependency. It is an unnecessary alternative
and the tools framework already does the right thing. Bump revisions.

Log message:
Recursive revision bump / recommended bump for gettext ABI change.

Log message:
Fix errno.

Log message:
Prevent paths to the build directories from being included in the package.
Bump PKGREVISION.

Log message:
Get rid of USE_PERL5.  The new way to express needing the Perl executable
around at either build-time or at run-time is:

	USE_TOOLS+=	perl		# build-time
	USE_TOOLS+=	perl:run	# run-time

Also remove some places where perl5/buildlink3.mk was being included
by a package Makefile, but all that the package wanted was the Perl
executable.